It provides an exceptional wet gloss finish with unmatched depth and clarity. Stirring must be uniform, especially the inner wall of the container, the bottom, etc, about 2-3 minutes. You can use glass rods, bamboo sticks, etc.
Bulk 1gallon kit : （16oz resin A + 16oz hardener B） 4 (Total 1Gallon). 64oz kit : （16oz resin A + 16oz hardener B） 2 (Total 64oz). CONCRETE AND PEBBLE COATING. Always keep the bottles sealed when. 32oz kit : 16oz resin A + 16oz hardener B (Total 32oz).
Features: Mix Ratio……………1:1 by volume Work time …………..30-45 minutes （Surface Fast Cure） Hardness………………..D70-80 Mixed Viscosity……….2500-3500cps. Chemical Resistance…….excellent Moisture Resistance……..excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80 ℃ (please don’t leave hot pans on it,a coaster needed)Note: 32oz kit : 16oz resin A + 16oz hardener B (Total 32oz) 64oz kit : 32oz resin A + 32oz hardener B (Total 64oz) Bulk 1gallon kit : （64oz resin A +64oz hardener B）*2 (Total 1Gallon) The resin specially designed with Low viscosity, convenient 1:1 mix ratio by volume, long pot life, room temperature curing system with great clarity and a high gloss finish. Perfect for tabletops, fiberglass work, small castings (under 1.2″ / 3cm), electrical potting, jewelry making, concrete – pebble coating, marine applications- boat building, & wood water proofing – repairs.Full cure time is 8-12 hours in Summer, 24 hours in Winter. Hardness range 70-80D Note: The resin mixed, pour No more than 150ml (75ml A +75ml B) Each time , with a thickness range of 0.4″ -1.2″ (1-3cm), to avoid bursting. and you can go as deep as you like,just make sure to work in stages. stay under 1.2″ per pour. after the surface film cures begin your second pour. the surface set time is roughly 1 hour at room temp.Features: Mix Ratio……………1:1 by volume Work time …………..30-45 minutes （Surface Fast Cure） Hardness………………..D70-80 Mixed Viscosity……….2500-3500cps. Chemical Resistance…….excellent Moisture Resistance……..excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80 ℃ (please don’t leave hot pans on it,a coaster needed) Approximate Coverage: 1.1m per 4L kit at 0 3cm thicknessAPPROVED APPLICATIONS:WOOD & METAL COATINGTABLETOPSCRAFTSJEWELRY MAKINGHOBBYIST AND CRAFT MAKINGPLAQUES AND FRAMESCONCRETE AND PEBBLE COATINGFIBERGLASS WET LAY-UPWATERPROOFING & SEALINGImportant This chemical needs to be stored in a dry, safe, temperature controlled environment. Always keep the lids tightly sealed when not in use. Remember, oxygen and moisture oxidize and can rapidly degrade the epoxy and hardener. Moisture is also a potential issue. Always keep the bottles sealed whennot in use. When applying this product, use gloves, goggles, and proper safety equipment. Please refer to the safety data sheet before using any of our epoxy products.PaymentDelivery detailsReturn policyAbout usContact usPaymentWe accept Paypal,Google Pay,VISA,Master Card,American Express and Discover.Delivery detailsWe usually ship from US within 1-3 business days with tracking number.Return policy30 days returns. Seller pays for return shipping.About usWe are a trustworthy and professional card protection supplier.Contact usIf need any assistance about our product and service,contact us for free at any time via eBay messages.
Operation steps 2:1 ratio for A & B glue by weight Pour into the mixing cup Stir it evenly for 2-3 minutes Add glitter or pigment if you need, then stir it, standing 30-60s Slowly pour mixed resin down the mold Add other decorative Tips for operation each time the resin mixed with a thickness range of under 2″ in summer, 2-4″ in winter to avoid bursting. and you can go as deep as you like, just make sure to work in stages. stay under 2″- 4″ per pour. After the surface film cures begin your second pour. the surface set time is roughly 4 hours at room temp. Full cure time is 48 hours in Summer, 48-72 hours in Winter. Hardness range 80-85DDeep Pour Clear Epoxy Resin 750g/24oz 1.5kg/48oz 3kg/96oz 6kg/192oz 12kg/384oz Kit – 2:1 By Weight Low viscosity non ToxicOperation steps2:1 ratio for A & B glue by weightPour into the mixing cupStir it evenly for 2-3 minutesAdd glitter or pigment if you need, then stir it, standing 30-60sSlowly pour mixed resin down the moldAdd other decorative The resin specially designed with Low viscosity, convenient 2:1 mix ratio by weight, long pot life, room temperature curing system with great clarity and a high gloss finish. The resin 2:1 mix ratio by weight (Not by volume), can deeper pour up to 2″-4″ one time in winter 750g / 24oz kit : 2 bottles 8oz resin A + 1 bottle 8oz hardener B (Total 24oz) 1.5kg / 48oz kit : 2 bottles 16oz resin A + 1 bottle oz hardener B (Total 48oz) 3kg / 96oz kit : 2 bottles 32oz resin A + 1 bottle 32oz hardener B (Total 96oz) 6kg / 192oz kit : 2 bottles 64oz resin A + 1 bottle 64oz hardener B (Total 192oz) 12kg / 384oz kit : 2 bottles 128oz resin A + 1 bottle 128oz hardener B (Total 384oz) Tips for operation each time the resin mixed with a thickness range of under 2″ in summer, 2-4″ in winter to avoid bursting.and you can go as deep as you like, just make sure to work in stages. stay under 2″- 4″ per pour. After the surface film cures begin your second pour.the surface set time is roughly 4 hours at room temp.Full cure time is 48 hours in Summer, 48-72 hours in Winter. Hardness range 80-85D This product cures to a brilliant high gloss finish. The finished product will be very rigid, smooth, clear, and display a brilliant high gloss finish similar to glass. Formulated to meet a variety of applications. Perfect for tabletops, fiberglass work, small castings (under 4″), electrical potting, jewelry making, concrete – pebble coating, marine applications- boat building, & wood water proofing – repairs. Features:Mix Ratio……………2:1 by weightWork time …………..4-6 hoursHardness………………..D80-85Mixed Viscosity……….2000-3000cps.Chemical Resistance…….excellentMoisture Resistance……..excellentFDA Compliant / Food grade: Yes, in its inert fully cured stateHeat resistance: up to 80℃ (please don’t leave hot pans on it,a coaster needed)Approximate Coverage: 12 square ft per 4kg at 1/8 inch thickness APPROVED APPLICATIONS:WOOD & METAL COATINGTABLETOPSCRAFTSJEWELRY MAKINGHOBBYIST AND CRAFT MAKINGPLAQUES AND FRAMESCONCRETE AND PEBBLE COATINGFIBERGLASS WET LAY-UPWATERPROOFING & SEALING Important This chemical needs to be stored in a dry, safe, temperature controlled environment. Always keep the lids tightly sealed when not in use. Remember, oxygen and moisture oxidize and can rapidly degrade the epoxy and hardener. Moisture is also a potential issue. Always keep the bottles sealed when not in use. When applying this product, use gloves, goggles, and proper safety equipment. Please refer to the safety data sheet before using any of our epoxy products.PaymentShipping detailsReturn policyAbout usContact usPaymentWe accept Paypal,Google Pay,VISA,Master Card,American Express and Discover.Shipping detailsWe usually ship from US within 1-3 business days with tracking number by USPS or UPS.Return policy30 days returns. Seller pays for return shipping.About usWe are a trustworthy and professional eBay seller.Contact usIf any problems about our product and service,contact us for free at any time via eBay messages.BrandFUNEPOXYColorClearHandmadeYesHardness80-85DModelClear Epoxy Resin
The resin 1:1 mix ratio by volume, 64oz kit is volume 64oz mixed, is the total volume 64OZ kit : 32oz resin A +32oz hardener B (Total 64oz) Pakage included : 2X 64oz Kit (Bulk 1 Gallon total) Specifications: Mix Ratio……………1:1 by volume Work time …………..30-45 minutes Hardness………………..D70-80 Mixed Viscosity……….2500-3500cps. Chemical Resistance…….excellent Moisture Resistance……..excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80℃ (please don’t leave hot pans on it,a coaster needed) Approximate Coverage: 12 square ft per gallon at 1/8 inch thicknessDescription:The clear epoxy coating and casting system features a 1:1 mix ratio, offering a pourable solution that is scratch and water resistant. It provides an exceptional wet gloss finish with unmatched depth and clarity. Formulated for all coating and step casting applications, it is ideal for coffee tables, river tables, side tables, bar tops, countertops, and small void filling live-edge tables. Each time mixed, pour No more than 150ml total, (that is 75ml A + 75ml B, A must be ≥ B), with a thickness range of ≤1.2″ to avoid bursting.Stay under 1.2″ per pour.After the surface film cures begin your second pour.This ultra-clear epoxy resin system is perfect for professional applications, delivering superior performance. The resin 1:1 mix ratio by volume, 64oz kit is volume 64oz mixed, is the total volume 64OZ kit : 32oz resin A +32oz hardener B (Total 64oz) Pakage included : 2X 64oz Kit (Bulk 1 Gallon total) Specifications:Mix Ratio……………1:1 by volumeWork time …………..30-45 minutesHardness………………..D70-80Mixed Viscosity……….2500-3500cps.Chemical Resistance…….excellentMoisture Resistance……..excellentFDA Compliant / Food grade: Yes, in its inert fully cured stateHeat resistance: up to 80℃ (please don’t leave hot pans on it,a coaster needed)Approximate Coverage: 12 square ft per gallon at 1/8 inch thickness Usage:1. The resin 1:1 mix ratio by volume, Stay under 1.2″ per pour.2. Stirring must be uniform, especially the inner wall of the container, the bottom, etc, about 2-3 minutes. You can use glass rods, bamboo sticks, etc. After mixed,this product is better to let stand for 3-5 minutes.before used in order to break the bubbles which produced when it was mixing in time.3.the surface set time is roughly 1 hour at room temp(the full cure time is 8-12 hours in summer and 12-24 hours in winter) the hardness range is 70-80D after full cure.4. Please try a little bit before using the product a lot, so that would master the skills and avoid mistakes.5. When using crystal glue, be careful not to stick it on your hands or body. If this happens, wipe off the glue with a cloth or paper towel, then rinse with water soap or detergent. Note:Please Store Away from LightKeep Away from Childrens ReachUse Proper PpeEach Time the Resin Mixed with a Thickness Range of ≤1.2″to Avoid Bursting Question：Q:Why are there bubbles in the finished product?A:Stir too fast when adjusting the glue, and pour into the mold before the bubbles have completely subsided. Or after pouring the glue into the mold, the inner wall of the mold is not observed. If there are bubbles, please cut them off in time.Q:Why is the finished product soft?A:Inaccurate adjustment of the glue ratio will cause the finished product to not solidify, and the glue will not be thoroughly mixed evenly during stirring, and there will be wire drawing in the glue, and the mold will be demolded if it is not completely solidified.Q:What should I do if I get Epoxy?A:It can be washed directly with water, or wiped with a nail remover towel before washing. Q:Can it be put in the sun or in the refrigerator?A:Do not expose to the sun for a long time. Excessive exposure to ultraviolet rays will make the finished product fade and yellow. Putting glue in the refrigerator will greatly extend the fixed time.PaymentDelivery detailsReturn policyAbout usContact usPaymentWe accept Paypal,Google Pay,VISA,Master Card,American Express and Discover.Delivery detailsWe usually ship from US within 1-3 business days with tracking number.Return policy30 days returns. Seller pays for return shipping.About usWe are a trustworthy and professional card protection supplier.Contact usIf need any assistance about our product and service,contact us for free at any time via eBay messages.
The resin 1:1 mix ratio by volume, 64oz kit is volume 64oz mixed, is the total volume 64OZ kit : 32oz resin A +32oz hardener B (Total 64oz) Pakage included : 2X 64oz Kit (Bulk 1 Gallon total) Specifications: Mix Ratio……………1:1 by volume Work time …………..30-45 minutes Hardness………………..D70-80 Mixed Viscosity……….2500-3500cps. Chemical Resistance…….excellent Moisture Resistance……..excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80℃ (please don’t leave hot pans on it,a coaster needed) Approximate Coverage: 12 square ft per gallon at 1/8 inch thickness.
Operation steps 2:1 ratio for A & B glue by weight Pour into the mixing cup Stir it evenly for 2-3 minutes Add glitter or pigment if you need, then stir it, standing 30-60s Slowly pour mixed resin down the mold Add other decorative Tips for operation each time the resin mixed with a thickness range of 3-5cm in summer, 5-10cm in winter to avoid bursting. and you can go as deep as you like, just make sure to work in stages. stay under 2″- 4″ per pour. After the surface film cures begin your second pour. the surface set time is roughly 4 hours at room temp. Full cure time is 48 hours in Summer, 48-72 hours in Winter. Hardness range 80-85DOperation steps2:1 ratio for A & B glue by weightPour into the mixing cupStir it evenly for 2-3 minutesAdd glitter or pigment if you need, then stir it, standing 30-60sSlowly pour mixed resin down the moldAdd other decorative The resin specially designed with Low viscosity, convenient 2:1 mix ratio by weight, long pot life, room temperature curing system with great clarity and a high gloss finish. The resin 2:1 mix ratio by weight (Not by volume), can deeper pour up to 4″ one time in winter 1.5kg / 48oz kit : 2 bottles 16oz resin A + 1 bottle oz hardener B (Total 48oz) 3kg / 96oz kit : 2 bottles 32oz resin A + 1 bottle 32oz hardener B (Total 96oz) 6kg / 192oz kit : 2 bottles 64oz resin A + 1 bottle 64oz hardener B (Total 192oz) 12kg / 3 Gallons kit : 2 bottles 1 Gallon resin A + 1 bottle 1 Gallon hardener B (Total 3 Gallons) Tips for operation each time the resin mixed with a thickness range of 3-5cm in summer, 5-10cm in winter to avoid bursting.and you can go as deep as you like, just make sure to work in stages. stay under 2″- 4″ per pour. After the surface film cures begin your second pour.the surface set time is roughly 4 hours at room temp.Full cure time is 48 hours in Summer, 48-72 hours in Winter. Hardness range 80-85D This product cures to a brilliant high gloss finish. The finished product will be very rigid, smooth, clear, and display a brilliant high gloss finish similar to glass. Formulated to meet a variety of applications. Perfect for tabletops, fiberglass work, small castings (under 4″), electrical potting, jewelry making, concrete – pebble coating, marine applications- boat building, & wood water proofing – repairs. Features:Mix Ratio……………2:1 by weightWork time …………..4-6 hoursHardness………………..D80-85Mixed Viscosity……….2000-3000cps.Chemical Resistance…….excellentMoisture Resistance……..excellentFDA Compliant / Food grade: Yes, in its inert fully cured stateHeat resistance: up to 80℃ (please don’t leave hot pans on it,a coaster needed)Approximate Coverage: 12 square ft per 4kg at 1/8 inch thickness APPROVED APPLICATIONS:WOOD & METAL COATINGTABLETOPSCRAFTSJEWELRY MAKINGHOBBYIST AND CRAFT MAKINGPLAQUES AND FRAMESCONCRETE AND PEBBLE COATINGFIBERGLASS WET LAY-UPWATERPROOFING & SEALING Important This chemical needs to be stored in a dry, safe, temperature controlled environment. Always keep the lids tightly sealed when not in use. Remember, oxygen and moisture oxidize and can rapidly degrade the epoxy and hardener. Moisture is also a potential issue. Always keep the bottles sealed when not in use. When applying this product, use gloves, goggles, and proper safety equipment. Please refer to the safety data sheet before using any of our epoxy products.PaymentShipping detailsReturn policyAbout usContact usPaymentWe accept Paypal,Google Pay,VISA,Master Card,American Express and Discover.Shipping detailsWe usually ship from US within 1-3 business days with tracking number by USPS or UPS.Return policy30 days returns. Seller pays for return shipping.About usWe are a trustworthy and professional eBay seller.Contact usIf any problems about our product and service,contact us for free at any time via eBay messages.BrandFUNEPOXYColorClearHandmadeYesHardness80-85DModelClear Epoxy Resin
Bulk 1gallon kit : （16oz resin A + 16oz hardener B） 4 (Total 1Gallon). 64oz kit : （16oz resin A + 16oz hardener B） 2 (Total 64oz). CONCRETE AND PEBBLE COATING. Always keep the bottles sealed when. 32oz kit : 16oz resin A + 16oz hardener B (Total 32oz).
Features: Mix Ratio……………1:1 by volume Work time …………..30-45 minutes （Surface Fast Cure） Hardness………………..D70-80 Mixed Viscosity……….2500-3500cps. Chemical Resistance…….excellent Moisture Resistance……..excellent FDA Compliant / Food grade: Yes, in its inert fully cured state Heat resistance: up to 80 ℃ (please don’t leave hot pans on it,a coaster needed).
